“Life is like riding a bicycle.  To keep your balance you must keep moving.”
–Albert Einstein
Showing posts with label direct current circuit. Show all posts
Showing posts with label direct current circuit. Show all posts

Saturday, May 15, 2010

AP Physics B & C - Multiple Choice Practice Questions on Electric Circuits Containing Resistors and Capacitors

Free response as well as multiple choice questions on direct current circuits containing resistors and capacitors are popular among question setters. Questions involving steady state are meant for AP physics B as well as AP physics C aspirants, where as questions involving RC transients are meant exclusively for AP physics C aspirants.

You will find questions in this section posted earlier on this site by performing a search using the search box on this page or by clicking on the label ‘direct current circuit’ below this page. Today we will discuss a few more practice questions in this section.

The following questions are meant for AP physics B as well as AP physics C aspirants:

(1) In the circuit shown in the adjoining figure the capacitors are fully charged. What is the potential difference across the 2 μF capacitor?

(a) 0.5 V

(b) 1 V

(c) 2 V

(d) 3 V

(e) 4 V

The parallel combination of the 6 μF and 2 μF capacitors is equivalent to a single 8 μF capacitor. Therefore, the 6 V battery is (in effect) connected in series with two 8 μF capacitors so that there will be a potential difference of 3 V across each 8 μF capacitor. Since the parallel combination of the 6 μF and 2 μF capacitors makes the lower 8 μF capacitor, the potential difference across the 2 μF capacitor is 3 V.

[The potential difference across the 6 μF capacitor also is 3 V].

(2) In the circuit shown in question no.1 what is the charge on the lower plate of the 6 μF capacitor under steady state?

(a) – 48 μC

(b) + 18 μC

(c) – 18 μC

(d) + 12μC

(e) – 12 μC

The lower plate of the 6 μF capacitor is connected to the negative terminal of the battery. The charge on the lower plate is therefore negative. As shown above (while answering question no.1), the potential difference across the 6 μF capacitor is 3 V. Therefore, the charge on the lower plate of the 6 μF capacitor is – (6 μF×3 V) = 18 μC [Remember Q = CV].

(3) In the circuit shown in question no.1 the battery has negligible internal resistance. What is the current through the 6 Ω resistor under steady state?

(a) 0.05 A

(b) 0.2 A

(c) 0.5 A

(d) 1 A

(e) zero

Under steady state the capacitors are fully charged and there is no charging current. The current through the 6 Ω resistor is therefore zero.

(4) The circuit shown in the adjoining figure is almost the same as that shown in question no.1, but a key K is included. The internal resistance of the battery is negligible. Suppose the key K is open and the capacitors are initially uncharged. What is the current through the 6 Ω resistor at the moment the key K is closed (and the capacitors begin to get charged)?

(a) 0.05 A

(b) 0.5 A

(c) 1 A

(d) 2 A

(e) zero

At the moment the key is closed, there are no charges on the capacitors to oppose the flow of charges delivered by the battery. The capacitors therefore allow the passage of the transients with ease and the only opposition to the flow of the charges in the circuit is that offered by the resistor. The initial current through the 6 Ω resistor is therefore 6 V/6 Ω = 1 A.

The following questions are for AP Physics C aspirants:

(5) Refer to the circuit shown in question no. 4. Initially the key K is open and the capacitors are uncharged. After closing the key, what time must be elapsed for the current through the 6 Ω resistor to become 1/e ampere (where ‘e’ is the base of natural logarithms)?

(a) 24 μs

(b) 48 μs

(c) 96 μs

(d) 0.01 s

(e) 0.1 s

The initial charging current I0 through the 6 Ω resistor is given by

I0 = V/R = 6 V/6 Ω = 1 A.

The time constant of an RC circuit is the time required for the charging current to reduce from its initial value I0 to (1/e)I0. If you remember this fact, you can immediately write down the answer as RC since I0 = 1 A in the present case. So the answer is 6 Ω×4 μF = 24 μs.

[Usually the time constant of an RC circuit is defined as the time required for the charge on the capacitor (or voltage across the capacitor) to grow from zero to (1– 1/e) times the final steady value. The growth of charge Q is exponential and is given by

Q = Q0 (1 – e–t/RC) where Q0 is the final steady charge.

The charging current I at time t after closing the key K is given by

I = dQ/dt = (Q0/RC)e–t/RC = (CV/RC)e–t/RC = (V/R)e–t/RC = I0e–t/RC.

Therefore, I = (1/e)I0 when t = RC]

(6) In the circuit shown in the adjoining figure the capacitor C is initially charged to have a potential difference V0 volt across it. The key K is initially open. When the key K is closed (at zero time), the potential difference across the capacitor becomes 0.5 V0 volt after a time t’ . What is the value of t’ ?

(a) 2 RC

(b) 0.5RC

(c) RC/ln2

(d) RC ln2

(e) RC

The potential difference V after time t is given by

V = V0 e–t/RC where ‘e’ is the base of natural logarithms.

Therefore we have 0.5 V0 = V0 e–t’/RC.

Or, et’/RC = 1/0.5 = 2 from which t’/RC = ln2

This gives t’ = RC ln2.


Tuesday, December 1, 2009

AP Physics B & C - Multiple Choice Practice Questions on Direct Current Circuits


Equations to be remembered for answering questions on direct current circuits and RC transients were posted on this site on 31st March 2008. You can access them by clicking on the label ‘direct current circuit’ below this post or by trying a search using the search box at the top of this page. Today we will discuss some more multiple choice practice questions in this section:
(1) A uniform copper wire of radius r and length L has resistance R at temperature T. If this wire is carefully stretched so that its radius becomes kr where k is a constant, its resistance at the temperature T will be
(a) kR
(b) R/k2
(c) k2R
(d) k4R
(e) R/k4
If A is the area of cross section of the wire before the stretching, we have
R = ρL/A where ρ is the resistivity (specific resistance) of the material of the wire.
When the radius becomes kr, the area of cross section of the wire becomes k2A. Since the volume of the wire is unchanged, the length of the wire becomes L/k2. The resistance of the wire after stretching therefore becomes R’ given by
R’ = ρ(L/k2)/k2A = ρL/ k4A = R/k4
[Note that the resistance of the wire after stretching is greater than R since k < 1].
(2) In the above question suppose the wire was stretched so that its length becomes 1.01 L. The resistance of the wire after stretching then becomes nearly
(a) 1.01R
(b) R/1.02
(c) 1.02R
(d) 1.04R
(e) R/1.04
Note that if a wire of resistance R is stretched so that its length becomes n times its original length, its area of cross section becomes (1/n) times its original area of cross section. The resistance of the wire therefore becomes n2R.
Since n = 1.01 the resistance after stretching is (1.01)2R =1.02R, nearly [Option (c)].
Here is a variation of question no.1:
(3) If the radius of a uniform metal wire of resistance R is changed by 1% by stretching it carefully under isothermal conditions, its resistance becomes
(a) 1.04R
(b) R/1.04
(c) 1.02R
(d) R/1.02
(e) 1.01R
We have R’ = R/k4 as shown in question no.1. Since the change (decrease) in the radius is 1%, k = 0.99.
Therefore, R’ = R/(0.99)4 = R/[1 – (0.01)]4 = R [1 – (0.01)]–4
This gives R’ = 1.04R, nearly.

(4) The resistance of an ammeter of range 2 A is R. The shunt resistance required to make its range 6 A is
(a) R
(b) R/5
(c) R/6
(d) R/2

(e) R/3

Let S be the shunt resistance required. When a current of 6 A is passed through the ammeter- shunt combination, 2 A should pass through the ammeter and the remaining 4 A should pass through the shunt (fig.). Therefore we have
2×R = 4×S, on equating the potential difference across the ammeter resistance R to the potential difference across the shunt resistance S.
This gives S = R/2
The following questions are for AP Physics C aspirants (even though AP Physics B aspirants also can try them):
(5) A power supply having internal resistance r drives a current through a load of resistance P. The heat developed in the load resistance is H. When the same power supply drives a current through another load of resistance Q for the same time t, the heat developed in the load resistance is H itself. The internal resistance of the power supply is for a time
(a) √(PQ)
(b) √[(P2 + Q2)/2]
(c) (P + Q)/2
(d) (P – Q)/2
(e) √[(P2 – Q2)/2]
Since H = I2Rt where I is the current through the load resistance R, we have
H = [V/(P+r)]2Pt = [V/(Q+r)]2Qt where V is the emf of the power supply.
[V/(P+r) is the current in the load resistance P and V/(Q+r) is the current in the load resistance Q].
From the above equation we have
P/(P+r)2 = Q/(Q+r)2
Or, P/(P2 +r2 +2Pr) = Q/(Q2+r2 + 2Qr)
Or, PQ2 + Pr2 + 2PQr = QP2 + Qr2 + 2PQr from which
r2(P – Q) = QP2 – PQ2
Or, r2(P – Q) = PQ(P – Q) so that r = √(PQ)




(6) A 12 V battery having internal resistance 0.2 Ω is being charged at a current of 2 A using the circuit shown in the figure. The generator which charges the battery has a terminal voltage of 16 V at this charging current. What is the value of the resistance R connected in the circuit?
(a) 0.2 Ω
(b) 0.8 Ω
(c) 1.8 Ω
(d) 2.6 Ω
(e) 3.4 Ω
The voltage between the terminals of the battery (terminal potential difference) while the battery is being charged (which is equal to the sum of the emf of the battery and the potential drop across its internal resistance) = 12 + 0.4 = 12.4 V.
[0.4 V is the voltage drop (2×0.2 volt) across the internal resistance of the battery].
Therefore, the voltage drop across the series resistance R is (16 – 12.4) V = 3.6 V.
Since the charging current is 2 A, we have 2 ×R = 3.6 from which R = 1.8 Ω.



You will find some useful multiple choice questions (with solution) in this section here.

Friday, April 11, 2008

AP Physics B & C – Multiple Choice Questions (for practice) on Direct Current Circuits

The essential formulae to be remembered in connection with direct current circuits were given in the post daied 31st March 2008. A couple of free response questions were posted on 5th April 2008. Today we will discuss a few multiple choice questions in this section.

In the circuit shown, the battery has some internal resistance. Answer the following questions numbered (1) and (2) in respect of the circuit:

Question No.(1):

The switch S has been closed for a long time and the capacitor C has been fully charged. If the voltage across the capacitor is found to be 3 V, what is the current flowing through the resistor R1?

(a) zero

(b) 0.2 A

(c) 0.5 A

(d) 0.6 A

(e) 6/11 A

Since the capacitor is fully charged, the voltage across the capacitor is equal to the steady voltage across the 6 Ω resistor R3. The current I flowing through R3 is therefore given by

I = 3 V/6 Ω = 0.5 A.

The current through R1 is the same as that through R3. So the correct option is 0.5 A.

Question No.(2):

What is the internal resistance of the battery?

(a) 0.2 Ω

(b) 0.5 Ω

(c) 1 Ω

(d) 18 Ω

(e) 6/11 A

The current I delivered by the battery can be written as

I = E/(R1+ R2+ R3+r) where E is the emf and r is the internal resistance of the battery. Since the current I is 0.5 ampere, we have

0.5 A = 9V/(5+6+6+r)Ω so that r = 1 Ω.

Question numbers (3), (4) and (5) given below relate to the adjoining circuit in which a current of 2A enters the network of resistors R1, R2, R3, R4 and R5 through the junction P and leaves through the junction Q.

Question No.(3):

The effective resistance between the junctions P and Q is

(a) 1 Ω

(b) 2 Ω

(c) 3 Ω

(d) 4 Ω

(e) 5 A

The resistors R1, R2, R3 and R4 make a balanced Wheatstone bridge since R1/R2 = R3/R4. No current can therefore pass through the resistor R5 so that it can be ignored. The circuit therefore reduces to 3Ω (which is the series combined value of 1Ω and 2Ω) in parallel with 6Ω (which is the series combined value of 2Ω and 4Ω). Therefore, the effective resistance between the junctions P and Q is (3×6)/(3+6) = 2 Ω.

Question No.(4):

The potential difference between the junctions P and Q is

(a) 2 V

(b) 4 V

(c) 6 V

(d) 8 V

(e) 10 V

Since the effective resistance between the junctions P and Q is 2 Ω (as shown above) and the current flowing into the network is 2 A, the potential difference (IR drop) between the junctions P and Q is 2×2 = 4 V.

Question No.(5):

The current flowing through the 4 Ω resistor (R4) is very nearly

(a) 0.567A

(b) 0.667 A

(c) 0.876 A

(d) 0.95 A

(e) 1 A

The resistor R5 can be ignored as we saw while answering question No.3. The current flowing through R4 is the current flowing through the lower parallel branch containing R3 and R4. The lower parallel branch has total resistance 6 Ω and the upper branch has total resistance 3 Ω. The current being inversely proportional to the resistance of the branch, the main current of 2A must get divided in the ratio 3:6 (= 1:2) between the lower and upper branches. The current through the lower branch must therefore be 2×(1/3) =2/3 A which is very nearly equal to 0.667 A.

[When current gets divided between two parallel branches, the current (I1) through one branch is given by

I1 = (Main current× Resistance of the other branch)/ Total resistance

In the present case current through the branch containing R4 = 2× (R1+R2)/ (R1+R2+ R3+R4) =

2× (1+2)/(1+2+2+4) = 2/3 = 0.667 A, very nearly].

You will find similar multiple choice questions (MCQ) with solution from different branches of physics at physicsplus.blogspot.com

Tuesday, April 8, 2008

AP Physics B & C –Answers to Free-Response Questions (for practice) on Direct Current Circuits

Two free response questions on direct current circuits were posted on 5th March 2008 for your practice. As promised, I give below the answers along with the questions.

Free Response Question No.1 (For AP Physics B and C)

A 10 V battery of negligible internal resistance is connected in series with a 4 Ω resistor R1, a 6 Ω resistor R2 and a 2 µF capacitor C as shown in the figure. A series combination of a 6 Ω resistor R3 and a switch S is connected across the series combination of R2 and C. The switch S is initially open and the battery has been connected for a long time.

(a) Determine the voltage across the capacitor C and the magnitude of the charge on one of its plates.

(b) The switch S is now closed. Determine the voltage across the capacitor C immediately after closing the switch S.

(c) Calculate the voltage across the capacitor C a long time after closing the switch S.

(d) Calculate the energy stored in the capacitor C a long time after closing the switch S.

(e) On closing the switch S, will the energy stored in the capacitor increase, decrease or remain unchanged? Put a tick mark against the correct option

Increase _____ Decrease _____ Remain unchanged _____

Justify your answer.

(a) Voltage across the capacitor is the same as the battery emf 10 V since the capacitor will charge through the resistors R1 and R2 to the full applied voltage on connecting it to the source for a long time.

(b) Immediately after closing the switch, the voltage across the capacitor is 10 volts it self since the capacitor cannot discharge immediately through R2 and R3.

(c) When the switch S is closed, the capacitor starts discharging through R2 and R3. After a long time, the voltage across the capacitor becomes equal to the voltage across R3.

Voltage across R3 = (Current through R3)×R3 = [10/(6+4)]×6 = 6 V.

(d) The energy stored in the capacitor = ½ CV2 = ½ ×(2×10–6)×62 = 36×10–6 coulomb = 36 μC.

(e) The energy will decrease since the voltage across the capacitor decreases from 10 V to 6 V.

Free Response Question No.2 (For AP Physics C)

In the adjoining figure the capacitor C is initially uncharged and the switches S1 and S2 are open. The battery has negligible internal resistance.

(a) The switches S1 and S2 are closed simultaneously. What will be the voltage across the resistor R2 immediately after closing the switches S1 and S2? Justify your answer.

(b) Determine the current through the resistor R2 immediately after closing the switches S1 and S2.

(c) A long time after closing the switches S1 and S2, the voltage across the resistor R1 was found to be 6 V. Calculate the value of the resistor R2.

(d) After a long time the switch S1 is opened but the switch S2 is retained in the closed condition. Calculate the voltage across the resistor R2 at the instant when 0.6 seconds have been elapsed after opening switch S1.

(a) The capacitor draws the maximum charging current initially and therefore effectively places a short circuit across the resistor R2 and the entire supply voltage of 9 volts appears across R1.

[This is the same as saying that the initial potential difference of zero volt across the capacitor cannot change abruptly since it takes time for the charges to get accumulated on the plates of the capacitor and to increase the P.D. across the plates].

(b) Since the initial voltage across the resistor R1 is 9 volts, the initial current through it (immediately after closing the switches S1 and S2) is 9 V/12 KΩ = 0.75 mA.

(c) The current flowing through R1 = 6V/12 KΩ = 0,5 mA.

The voltage across R2 = 9 V – 6 V = 3 V.

Since the same current of 0.5 mA flows through R1 and R2 we have

R2 = 3 V/0.5 mA = 6 KΩ.

(d) During the discharge of a capacitor through a resistance R, the charge Q on the capacitor at time t is given by Q =Q0 e–t/RC where Q0 is the initial charge. Since V = Q/C, the voltage V across the capacitor is given by

V = (Q0/C) e–t/RC = V0 e–t/RC where V0 is the initial voltage which is 3 volts.

After 0.6 seconds, the voltage across the capacitor (which is also the voltage across R2) is given by

V = 3×e–0.6/0.6, since RC = R2C = 6000 Ω × 100×10–6 F = 0.6 second.

Thus V = 3×e–1 = 1.104 volt (very nearly)

Saturday, April 5, 2008

AP Physics B & C –Two Free-Response Questions (for practice) on Direct Current Circuits

Free response questions help the examiner to assess your standard from different angles and to some extent the evaluation will be subjective. But you can rest assured that the questions are so set that they are as specific as practicable. You must be very careful in presenting your answers in respect of free-response questions. Since the words “determine”, “derive”, “calculate”, “ justify”, “explain”, “what is”, “sketch” and “plot” have precise meanings in the AP Physics examination, you must thoroughly understand their significance so that you can give enough details wherever required and refrain from giving unwanted details where they will be sheer waste of time.

Here are two typical free response questions on direct current circuits. The first question is meant for both AP Physics B and C while the second question is meant for AP Physics C only.

(1) A 10 V battery of negligible internal resistance is connected in series with a 4 Ω resistor R1, a 6 Ω resistor R2 and a 2 µF capacitor C as shown in the figure. A series combination of a 6 Ω resistor R3 and a switch S is connected across the series combination of R2 and C. The switch S is initially open and the battery has been connected for a long time.

(a) Determine the voltage across the capacitor C and the magnitude of the charge on one of its plates.

(b) The switch S is now closed. Determine the voltage across the capacitor C immediately after closing the switch S.

(c) Calculate the voltage across the capacitor C a long time after closing the switch S.

(d) Calculate the energy stored in the capacitor C a long time after closing the switch S.

(e) On closing the switch S, will the energy stored in the capacitor increase, decrease or remain unchanged? Put a tick mark against the correct option

Increase _____ Decrease _____ Remain unchanged _____

Justify your answer.

The above question carries 15 points.

(2) In the adjoining figure the capacitor C is initially uncharged and the switches S1 and S2 are open. The battery has negligible internal resistance.

(a) The switches S1 and S2 are closed simultaneously. What will be the voltage across the resistor R2 immediately after closing the switches S1 and S2? Justify your answer.

(b) Determine the current through the resistor R2 immediately after closing the switches S1 and S2.

(c) A long time after closing the switches S1 and S2, the voltage across the resistor R1 was found to be 6 V. Calculate the value of the resistor R2.

(d) After a long time the switch S1 is opened but the switch S2 is retained in the closed condition. Calculate the voltage across the resistor R2 at the instant when 0.6 seconds have been elapsed after opening switch S1.

This question carries 15 points.

Try to answer the above questions. I’ll be back shortly with model answers for you.